How to Replace a Tub in Your Bathroom
How to Replace a Tub in Your Bathroom
Blog Article
What are your concepts about Installing A Bathtub?
Installing a bath tub isn't specifically rocket science, yet it does call for solid plumbing, carpentry, and also in some cases, tiling abilities. Replacing an old bath tub with a new one is additionally a moderately hard job. If the old bathtub is readily easily accessible, the project can relocate quickly; if you need to open a wall surface to eliminate the old bathtub and place the new tub, the task is a lot harder. In either case, the job is within a home handyman's skills, although you will certainly need an assistant to move out the old bathtub and embeded in the brand-new one. Ensure you have actually qualified yourself for the task and fit trying it. Instead of employing a service provider to take over a halfway-completed task, it is better to think about using one before you begin. Opportunities are you might need an expert plumber to make tube connections.
This short article will certainly help you set up a brand-new bathtub in your restroom if you have actually already purchased a new bathtub and don't require to transform the arrangement of your previous water system pipelines.
Your tools as well as product list should comprise the following:
Getting ready for the Installment
Firstly, the supporting framework provided with the bathroom should be fitted (if required) according to the maker's directions. Next off, fit the faucets or mixer to the bath tub. When suitable the tap block, it is very important to make certain that if the tap includes a plastic washing machine, it is fitted in between the bathroom and also the taps. On a plastic bath, it is also practical to fit a sustaining plate under the faucets device to stop strain on the bathtub.
Fit the flexible tap adapters to the bottom of the two taps using 2 nuts and olives (sometimes provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the outlet through the hole in the bathroom. Make use of the nut provided by the maker to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the adaptable overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which should be fitted inside the bath. See to it you make use of every one of the supplied washers.
Connect the catch to the bottom of the waste electrical outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Connect the bottom of the overflow tube in a comparable manner.The bath ought to now prepare to be suited its final position.
Removing Old Touches
If you require to replace old taps with brand-new ones as a part of your setup, then the first thing you should do is separate the water system. After doing so, switch on the taps to drain pipes any type of water staying in the system. The process of getting rid of the existing taps can be quite bothersome because of the restricted accessibility that is typically the case.
Make use of a container wrench (crowsfoot spanner) or a tap device to undo the nut that connects the supply pipelines to the taps. Have a cloth all set for the staying water that will come from the pipelines. As soon as the supply pipes have been gotten rid of, utilize the exact same tool to loosen up the nut that holds the faucets onto the bath/basin. You will require to quit the single faucets from transforming during this procedure. As soon as the taps have actually been gotten rid of, the holes in the bath/basin will certainly need to be cleaned of any type of old sealing substance.
Before moving on to fit the brand-new taps, compare the pipeline connections on the old faucets to the brand-new taps. If the old faucets are longer than the new faucets, after that a shank adapter is required for the brand-new taps to fit.
Installing the Tub
Using both wooden boards under its feet, place the tub in the required position. The wooden boards are handy in uniformly spreading the weight of the bath tub over the location of the boards rather than concentrating all the weight onto four tiny points.
The following objective is to guarantee that the bath tub is leveled all round. This can be achieved by examining the spirit level as well as readjusting the feet on the bathtub till the spirit level checks out degree.
To install faucets, fit all-time low of the furthest versatile faucet connector to the proper supply pipe by making a compression join; after that do the exact same for the other tap.
Activate the supply of water and also inspect all joints and also new pipework for leakages and tighten them if needed. Load the tub as well as also examine the overflow outlet as well as the regular outlet for leakages.
Ultimately, repair the bathroom paneling as explained in the supplier's instruction manual. Tiling as well as securing around the bathtub must wait till the bathtub has actually been made use of a minimum of once as this will certainly settle it into its last placement.
Fitting New Touches
If the tails of the brand-new taps are plastic, then you will certainly require a plastic connector to avoid damages to the thread. One end of the connector fits on the plastic tail of the faucet and also the other end offers a link to the existent supply pipes.
If you require to fit a monobloc, after that you will certainly require minimizing couplers, which links the 10mm pipeline of the monobloc to the standard 15mm supply pipe.
Next off, place the faucet in the mounting hole in the bath/basin making sure that the washing machines remain in area between the tap as well as the sink. Protect the faucet in position with the manufacturer provided backnut. When the tap is safely in position, the supply pipelines can be connected to the tails of the taps. The taps can either be linked by using corrugated copper piping or with typical faucet adapters. The previous kind should be connected to the tap ends first, tightening only by hand. The supply pipes can later be linked to the various other end. Tighten up both ends with a spanner after both ends have actually been attached.
Tiling Around the Bath tub
In the location where the bathroom fulfills the tile, it is necessary to seal the joins with a silicone rubber caulking. This is essential as the fitting can move enough to break a stiff seal, triggering the water to permeate the wall between the bath as well as the tiling, resulting in problems with moisture as well as possible leaks to the ceiling below.
You can choose from a variety of coloured sealants to blend in your components and also installations. They are marketed in tubes as well as cartridges, as well as are capable of sealing gaps up to a width of 3mm (1/8 inch). If you have a bigger void to load, you can load it with spins of soaked newspaper or soft rope. Remember to always load the bath tub with water prior to sealing, to allow for the movement experienced when the tub remains in usage. The sealer can break fairly very early if you do not take into consideration this movement before securing.
Conversely, ceramic coving or quadrant ceramic tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are also conveniently readily available on the market. It is advisable to fit the floor tiles making use of water-resistant or waterproof adhesive and also cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Hopefully you enjoyed reading our topic about How to Install a Bathtub. Thanks for taking time to read our article post. Kindly take the opportunity to promote this blog post if you enjoyed reading it. We appreciate reading our article about How to Install a Bathtub Yourself.
Schedule Now Report this page